![Product top banner](https://ab-bhs-ca-3.abtra.ovh/static/lpwarehouse/images/top-banner.jpg)
![](https://cdn.abtra.com/lpwarehouse/attachments/vspfiles/photos/1206-MX-2.jpg)
1206-MX 36V 300A Ezgo Pds Control
![Shipping image 0](https://ab-bhs-ca-3.abtra.ovh/static/lpwarehouse/images/banner-arrival-time.png)
![Shipping image 1](https://ab-bhs-ca-3.abtra.ovh/static/lpwarehouse/images/banner-guaranteed-fit.png)
![Shipping image 2](https://ab-bhs-ca-3.abtra.ovh/static/lpwarehouse/images/banner-international-shipping.png)
1206-MX 36V 300A E-Z-Go PDS Controller
Category: Curtis Parts
Product Description
This is a 36V 300A Precision Drive System (PDS) Controller for E-Z-Go Golf Carts with Parts Number: 1206-MX or 1206MX.
Cross Reference:
CL7007825, CT1206-MX, EZ609083, EZ73263G01, EZ73326G01, EZ73326G02, EZ73326G04, EZ73326G05, EZ73326G06, EZ73326G07, EZ750RBLTCNTRL, HU3178568R, PHA000029430, YP1500247-45R, 7007825, 1206-MX, 609083, 73263G01, 73326G01, 73326G02, 73326G04, 73326G05, 73326G06, 73326G07, 750RBLTCNTRL, 3178568R, A000029430, 1500247-45R
Suggested Accessories Part Numbers:
76-1415-GOLF, 76-908HRNS48V, 76-908R3648BNJO, 94-CM174, 100-586117111, 24-CBHF2-EZ36, 43-8012-30, 76-1415-GOLF, 76-908HRNS48V, 76-908R3648BNJO, 94-CM174, 100-586117111, 24-CBHF2-EZ36, 43-8012-30, 76-1415-GOLF, 51-FX302G019K, 51-FX302G024K, 51-FX302G026K, 51-FX503G019K, 51-FX503G024K, 51-FX503G026K, 76-1206MX-4301, 76-1268-5502EKP
Application: The Curtis 1206MX PDS Controller fits all E-Z-Go Electric 2000 and up golf carts.
Product Specifications
Specifications of the 1206MX E-Z-Go Controller:
Voltage | 36V |
Current | 300A |
Controller Type | PDS (Precision Drive System) |
Weight | 2 lbs. |
Dimension | 12 x 12 x 8 in |
Condition | Rebuilt |
Curtis 1206MX PDS Controller
The Curtis 1206MX is a remanufactured PDS Controller for E-Z-Go Electric 2000 and above golf carts. It is a solid state speed controller for the cart motor. It is responsible for regulating the speed level and performance of your vehicle while maintaining E-Z-Go safety standards.
![An image of a 1206-MX Controller](/v/vspfiles/assets/images/cs24-netz-3.jpg)
Figure: 1206MX E-Z-Go Controller
Pre-installation Tests
It is necessary to perform a set of tests according to the instruction manual before installing the EZGO 1206MX Controller. After installation, you may encounter problems that may be due to a faulty controller or a faulty cart. The following tests will help diagnose if the fault is a cart fault or a controller fault.
CHECK MOTOR WINDINGS:
- Set your VOM to RESISTANCE (Ω).
- With your motor disconnected, measure A1 to A2. This must measure BETWEEN .3Ω and 1Ω.
- With your motor disconnected, measure F1 to F2. This must measure BETWEEN 1Ω and 2Ω.
- With your motor disconnected, measure A1 to F1. This must measure OPEN.
- With your motor disconnected, measure F1 to motor case. This must measure greater than 5MΩ.
CHECK MAIN SOLENOID:
- Disconnect all wires from the main solenoid.
- Set your VOM to RESISTANCE (Ω).
- Measure the solenoid coil. This must measure NO LESS than 100Ω.
- Connect VOM leads to the main solenoid lugs.
- Attach jumpers from the main battery positive and negative to the coil (small terminals).
- Meter must jump from infinity to LESS THAN 3Ω.
- Remove jumpers and reconnect solenoid wiring from the harness. (If suppression diode is present, the non-banded side must go the blue wire – pin J1-6 from the controller.)
CHECK COTHERM:
- Inspect the cotherm (insulating material) mounted to the heat sink for holes, debris, and tears.
- Repair or replace, if necessary.
CHECK THE CART WIRE HARNESS:
- Check the connectors on the wire harness for corrosion, loose, broken, burnt or missing pins.
- Repair or replace pins as necessary.
Warranty Information
The EZGO 1206MX Controller comes with a 6-months limited warranty, extendable up to 36 months.
Frequently Asked Questions
Is this Curtis 1206MX a new Controller?
No, the Curtis 1206MX Controller is a rebuilt item.
What is the current rating of the Curtis 1206MX Controller?
This Controller is rated at 300 Amps.
Do I need to pay a core charge for the EZGO 1206MX Controller?
Yes, all remanufactured and rebuilt items are subject to a core charge. A core charge is refundable. The refund amount will be determined by the status of the core returned.
Which carts can use this Curtis 1206MX?
You can use the Curtis 1206MX Controller controller with any E-Z-Go Electric carts of Model 2000 and above.
More Parts For EZGO Golf Cart
Beside Curtis 1206MX Controller, if you need More Electrical Parts for EZGO Golf Carts, we have a huge collection of
- ITS Converter
- RXV Bleeder
- 48V Ezgo LSV
- DCS Control
- Cart Battery Charger
- 36V Handle Cord
- Charging Receptacle Repair Kit
- 48V RXV DC Handle, and many more!
![An image of electric E-Z-GO Golf Cart Parts collection at Lift Parts Warehouse](/v/vspfiles/assets/images/EZGO Electrical Parts.png)
Figure: A part of electric E-Z-GO Golf Cart Parts collection at Lift Parts Warehouse
Are you looking for something else? Please browse our Part Catalog here. Lift Parts Warehouse provides quality aftermarket parts at a very reasonable price. All parts come with a limited 1 Year Warranty. We also guarantee a 100% fit for our parts.
Customer Reviews
You need to be logged in to submit a review.
Questions & Answers
Fetching questions...